Differences
This shows you the differences between two versions of the page.
— |
engineer-mechanical:inventor-vise [2017/12/01 22:18] (current) |
||
---|---|---|---|
Line 1: | Line 1: | ||
+ | === Machine Vise === | ||
+ | * {{engineer-mechanical:inventor-vise:td12thch14p456.png|Figure 1-0 Machine Vise from Technical Drawing, 12th Ed by Giesecke}} | ||
+ | * Technical Drawing, 12th Edition by Giesecke, Mitchell, Spencer, Hill, Dygdon & Novak. Figure 14.80 - Machine Vise. Prob. 14.52: (1) Draw details. (2) Draw assembly. If assigned, convert dimensions to the decimal-inch system or redesign with metric dimensions. ([[http://jefferyjjensen.com/secure/pdf/Drafting/TechnicalDrawing12th-Giesecke/TDp456.pdf|secure pdf]]) | ||
+ | |||
+ | === Project: Vise Assembly === | ||
+ | * {{engineer-mechanical:inventor-vise:ch13-vise-assembly.png|Figure 1-0 Vise Assembly}} | ||
+ | * <HTML><iframe width="560" height="315" src="https://www.youtube.com/embed/tZ8Y39oSM2E" frameborder="0" allowfullscreen></iframe></HTML> | ||
+ | |||
+ | == Vise Base == | ||
+ | * {{engineer-mechanical:inventor-vise:ch13-vise-basea.png|Figure 2-0 Vise Base}} | ||
+ | * Step 1 - Create 2D sketch of the front view with dimensions from Figure 3-0. Then extrude the shape 3.5". | ||
+ | * {{engineer-mechanical:inventor-vise:ch13-vise-basefront2db.png|Figure 3-0 Vise Base 2D Sketch - Front View}} | ||
+ | * Step 2 - Create front circle | ||
+ | * {{engineer-mechanical:inventor-vise:ch13-vise-baseright2d.png|Figure 4-0 Vise Base 2D Sketch - Right View}} | ||
+ | * Create a new sketch on the right view. Draw a circle with radius 0.75" at the midpoint of the top line. | ||
+ | * Extrude the 2D sketch 1.25", with JOIN option | ||
+ | * Step 3 - Create front screw hole | ||
+ | * Create another 2D sketch and place a point at the center of the circle with radius 0.75". Then finish sketch. | ||
+ | * Use the Hole command to create hole with diameter 0.625" and hole depth of 1.25" | ||
+ | * Step 4 - Create 1.5" and 1.25" slots that cut through the entire base. | ||
+ | * Extrude 2D sketch 8" | ||
+ | * {{engineer-mechanical:inventor-vise:ch13-vise-baseslots.png|Figure 5-0 Vise Base Slots 2D Sketch}} | ||
+ | * {{engineer-mechanical:inventor-vise:visebaseviews.gif|Figure 6-0 Vise Base in multiple views}} | ||
+ | * Step 5 - Create securing bolt tabs at the vise base | ||
+ | * {{engineer-mechanical:inventor-vise:ch13-vise-baseextension2d.png|Figure 5-0 Vise Base 2D Sketch - bottom Extension Tabs}} | ||
+ | * {{engineer-mechanical:inventor-vise:ch13-visebase-p13-45.png|Figure 6-0 Vise Base Complete}} | ||
+ | |||
+ | == Vise Jaw == | ||
+ | * {{engineer-mechanical:inventor-vise:ch13-vise-jaw.png|Figure 1-0 Vise Jaw}} | ||
+ | * Step 1 - create a 2D sketch of the right view and extrude 1.75" | ||
+ | * {{engineer-mechanical:inventor-vise:ch13-vise-jaw2dright.png|Figure 2-0 Vise Jaw 2D Sketch - Right View}} | ||
+ | * Step 2 - create a 2D sketch on the front view, extrude 3.5" with Join option. | ||
+ | * {{engineer-mechanical:inventor-vise:ch13-vise-jaw2dfront.png|Figure 3-0 Vise Jaw 2D Sketch - Front View}} | ||
+ | * Step 3 - create a point at the center of the circle in a 2D sketch. After you finish the sketch, use the Hole command, diameter 0.75" and depth 0.5" | ||
+ | * {{engineer-mechanical:inventor-vise:ch13-vise-jawhole.png|Figure 4-0 Vise Jaw Hole}} | ||
+ | |||
+ | == Vise Key == | ||
+ | * Step 1 - create a key that fits into the slots of the jaw. Key dimensions are Length=1.75", Height=0.1875", and Width=0.375". Remember Inventor is picky when constraining parts, so a part that has a width of 1.33" will not constrain to a part width of 1.333" even though we know it is the same. | ||
+ | * {{engineer-mechanical:inventor-vise:ch13-vise-jawkeyp13-46.png|Figure 4-0 Vise Jaw Key Dimensions}} | ||
+ | * {{engineer-mechanical:inventor-vise:ch13-vise-jawkey.png|Figure 4-0 Vise Jaw Key}} | ||
+ | |||
+ | == Vise Screw == | ||
+ | * Step 1 - create a 2D sketch of a circle with a diameter of 0.625" then extrude a length of 6.5" | ||
+ | * Step 2 - on one end, create a 2D sketch of a circle with a diameter of 0.75" then extrude it a length of 1" | ||
+ | * {{engineer-mechanical:inventor-vise:ch13-visescrew2dend.png|Figure 1-0 Vise Screw 2D Sketch}} | ||
+ | * Step 3 - on the other end, create a 2D sketch of a circle with a diameter of 0.75" then extrude it a length of 0.5" | ||
+ | * Step 4 - on the end with the 1" extrusion, create a offset work plane (tangent to surface and parallel to plane). Then draw a circle with diameter 0.375" offset 0.5" from the end. | ||
+ | * {{engineer-mechanical:inventor-vise:ch13-vise-screw2dendhole.png|Figure 2-0 Vise Screw 2D Sketch}} | ||
+ | * Step 5 - Finally extrude the circle to create the hole. | ||
+ | |||
+ | == Vise Handle Rod == | ||
+ | * Step 1 - create a cylinder with a diameter 0.375" and length 5" | ||
+ | * {{engineer-mechanical:inventor-vise:ch13-vise-screwhandlerod.png|Figure 1-0 Vise Screw Handle Rod}} | ||
+ | |||
+ | == Vise Handle Knob == | ||
+ | * Step 1 - create a cylinder with a diameter 0.625" and length 0.75" | ||
+ | * Step 2 - create a point at the center of the 0.625" circle | ||
+ | * Step 3 - create a hole at this point, diameter 0.375" and hole depth 0.5" | ||
+ | * Step 4 - apply a chamfer of 0.0625" to each outside end of the knob | ||
+ | * {{engineer-mechanical:inventor-vise:ch13-vise-screwhandleknob.png|Figure 1-0 Vise Screw Handle Knob}} | ||
+ | |||
+ | |||
+ | === References === | ||
+ | * [[http://www.besseytools.com/en/index.php|BESSEY Tools]] | ||
+ | * [[http://www.groz-tools.com/index.cfm?md=Content&sd=Product&ProductID=128|Groz-Tools.com]] DPV-STD-125 vise from www.grozusa.com | ||
+ | * [[http://www.wiltontools.com|Wilton Tools]] technical service 800-274-6846 (8-5pm CST Mon-Fri) spoke with lady on 3/14/2014 at 10:55am (PST) and they don't provide any CADD drawing for their vises and she doesn't know of any other company that does, so she wasn't helpful. | ||
+ | * Textbook: Technical Drawing, 12th Ed by Giesecke, Mitchell, Spencer, Hill, Dygdon, and Novak, Chapter 14 Design and Working Drawings, p. 456 ([[http://jefferyjjensen.com/secure/pdf/inventor/TechnicalDrawing12th-Giesecke/TDp456.pdf|secure PDF]]) | ||